PA塑料(尼龙)
(聚酰胺)
称:Polyamide 比重:PA6-1.14克/立方厘米 PA66-1.15克/立方厘米 PA1010-1.05克/立方厘米 成型收缩率:PA6-0.8-2.5% PA66-1.5-2.2% 成型温度：220-300℃ 干燥条件：100-110℃ 12小时
坚韧,耐磨,耐油,耐水,抗酶菌,但吸水大.
尼龙6弹性好,冲击强度高,吸水较大
尼龙66性能优于尼龙6,强度高,耐磨性好
尼龙610与尼龙66相似,但吸水小,刚度低
尼龙1010半透明,吸水小,耐寒性较好适于制作一般机械零件,减磨耐磨零件,传动零件,以及化工,电器,仪表等零件
供应PA66德国巴斯夫A3WG315％玻璃纤维增强
供应PA66德国巴斯夫A3HG5
供应PA66德国巴斯夫8233G.25％玻璃纤维增强
供应PA66德国巴斯夫A3WG6.30％玻璃纤维增强
供应PA66德国巴斯夫A3EG5.25％玻璃纤维增强
供应PA66德国巴斯夫A3EG7.BK2318935％玻璃纤维增强
供应PA66德国巴斯夫A3HG7.35％玻璃纤维增强
未增强UltramidA,B(尼龙6,66)
PA66尼龙A3K --注塑级。含稳定剂，流动性好。适合电器绝缘制品和工程零件。
PA66尼龙A3W --注塑级，耐热老化。适于长期高温使用的零件。
PA66尼龙B3S --注塑级。容易流动，固化快，含稳定剂。适合薄壁制品如罩，夹具，销钉，夹板等，紧固件。
PA plastic (nylon)
(Polyamide)
Scale: Polyamide Specific gravity: PA6-1.14g/cm3 PA66-1.15g/cm3 PA1010-1.05g/cm3 Molding shrinkage: PA6-0.8-2.5% PA66-1.5-2.2% Molding temperature: 220-300 ℃ Drying conditions: 100-110 ℃ 12 hours
Tough, wear-resistant, oil resistant, water resistant, enzyme resistant, but with high water absorption
Nylon 6 has good elasticity, high impact strength, and high water absorption
Nylon 66 has better performance than nylon 6, high strength, and good wear resistance
Nylon 610 is similar to nylon 66, but has low water absorption and stiffness
Nylon 1010 is semi transparent, with low water absorption and good cold resistance. It is suitable for making general mechanical parts, wear reducing and wear-resistant parts, transmission parts, as well as chemical, electrical, instrument and other parts
Supply PA66 German BASF A3WG315% glass fiber reinforced
Supply PA66 BASF A3HG5, Germany
Supply PA66 BASF Germany 8233G.25% glass fiber reinforced
Supply PA66 German BASF A3WG6.30% glass fiber reinforced
Supply PA66 German BASF A3EG5.25% glass fiber reinforced
Supply PA66 BASF Germany A3EG7.BK2318935% glass fiber reinforced
Supply PA66 German BASF A3HG7.35% glass fiber reinforced
Unreinforced UltramedA, B (nylon 6,66)
PA66 nylon A3K - injection grade. Contains stabilizers and has good flowability. Suitable for electrical insulation products and engineering parts.
PA66 nylon A3W - injection grade, heat-resistant and aging resistant. Parts suitable for long-term high-temperature use.
PA66 nylon B3S - injection grade. Easy to flow, fast curing, containing stabilizers. Suitable for thin-walled products such as covers, fixtures, pins, plywood, and fasteners.
