供应pa66德国巴斯夫 a3eg3 bk00564玻璃纤维15增强，热稳定
pa66德国巴斯夫 a3eg3玻璃纤维15增强，热稳定
pa66德国巴斯夫 a3eg5玻璃纤维25增强
pa66德国巴斯夫 a3eg6 bk00564玻璃纤维30增强
pa66德国巴斯夫 a3eg6玻璃纤维30增强，热稳定
pa66德国巴斯夫 a3eg7 bk00564玻璃纤维35增强，热稳定
pa66德国巴斯夫 a3eg7 bk23189玻璃纤维35增强，热稳定
德国巴斯夫PA66 树脂在包装后储存时表面发黄现象的产生, 可以降低PA66树脂在包装时的温度及包装袋内的氧含量。为了既能保证干燥后的PA66树脂的水分又能降低PA66树脂在包装时的温度,由华韵公司出售可以采取如下方法:1在PA66树脂干燥后的物料输送管线上加装冷冻水夹套, 利用热量交换原理来降低干燥后的PA66树脂表面温度;2在包装时采用抽真空的方法降低德国巴斯夫PA66树脂包装袋内的氧含量。另外, 为了能更有效地预防干燥后的PA66树脂在包装后储存时表面发黄现象的发生及尽可能地降低在包装时PA66树脂的温度, 还要尽量做到:干燥后的PA66树脂在包装前要在成品料仓内暂存36 h, 待物料温度充分下降后再进行包装;包装后的PA66树脂垛盘在储存时, 要采取垛盘间距保持在15 cm左右的存放距离, 以利于通风和散热。
Supply PA66 BASF Germany a3eg3 bk00564 glass fiber 15 reinforced, thermally stable
PA66 German BASF a3eg3 glass fiber 15 reinforced, thermally stable
PA66 BASF Germany a3eg5 glass fiber 25 reinforced
PA66 BASF Germany a3eg6 bk00564 glass fiber 30 reinforced
PA66 German BASF a3eg6 glass fiber 30 reinforced, thermally stable
PA66 BASF Germany a3eg7 bk00564 glass fiber 35 reinforced, thermally stable
PA66 BASF Germany a3eg7 bk23189 Glass fiber 35 reinforced, thermally stable
The occurrence of yellowing on the surface of BASF PA66 resin during storage after packaging can reduce the temperature of PA66 resin during packaging and the oxygen content in the packaging bag. In order to ensure the moisture content of the dried PA66 resin and reduce the temperature of the PA66 resin during packaging, Huayun Company can adopt the following methods: 1. Install a chilled water jacket on the material delivery pipeline of the dried PA66 resin, and use the principle of heat exchange to reduce the surface temperature of the dried PA66 resin; 2. During packaging, vacuum is used to reduce the oxygen content in BASF PA66 resin packaging bags in Germany. In addition, in order to more effectively prevent the occurrence of yellowing on the surface of dried PA66 resin during storage after packaging and minimize the temperature of PA66 resin during packaging, it is also necessary to try to: the dried PA66 resin should be temporarily stored in the finished product warehouse for 36 hours before packaging, and packaging can only be carried out after the material temperature has fully decreased; When storing packaged PA66 resin pallets, a storage distance of about 15 cm should be maintained between pallets to facilitate ventilation and heat dissipation.
